Car Components Bodywork 

Lubricating hinges, pedals and locks

Put a little clean engine oil on the pivot point above a pedal with a pendant action.

Most brake and clutch pedals have a pendant action, and the pivoting parts will be above them, behind the dashboard. Use a torch to see them if necessary.

Pedals with nylon bushes do not need oiling. Pedals that swing on a steel rod need a regular injection of engine oil at pivots and on rubbing surfaces.

Place old newspaper under the pedals to catch drips, and clean off any surplus with a cloth. Wipe off oil that drips on to pedal rubbers with methylated spirit on a cloth.

Most accelerators have pendant pedals. Locate the pivot point – it is probably under the dashboard or beneath the bonnet. Lubricate metal-to-metal points with clean engine oil.

Some cars have accelerator pedals pivoted at the floor. Lift the carpet to avoid marking it, then lubricate the metal hinge with clean engine oil. If a floor-pivoted pedal is fixed to a shaft that operates through a metal tube, lubricate the inside of the tube.

Another type of accelerator pedal is called an organ pedal. It is hinged to the floor, and the pedal operates a normal pendant linkage. Lubricate the metal-to-metal links.

Rubber hinges do not need maintenance. Pedals bearing on a roller or pad do not need oiling, but keep them free from dust and fluff.

Oiling hinges and restrainers

A plain hinge can be sprayed with lubricant.

On door hinges lubricate friction surfaces and hinge pins with clean engine oil, wiping away any residue with a cloth.

Most car hinges have hollow, rolled-steel hinge pins with plastic caps top and bottom. Prise off the upper cap with a screwdriver and fill the pin with heavy gear oil – rear axle oil is ideal. Replace the cap, and wipe the hinge clean.

Take the cap off a hollow hinge and fill the pin with heavy oil.

THinges that are not hollow and do not have plastic caps can be sprayed with penetrating lubricant from an aerosol can if the hinge has stiffened. Once the action has eased, lubricate the hinge regularly with clean engine oil.

Lubricate the restrainer with clean engine oil.

The door restrainer, or check strap, is designed to prevent the door being opened too far, which damages the hinges so that the door no longer closes properly.

Some door restrainers include a mechanism for spring pressure against a peg, to keep the door open and prevent the wind from closing it when people are getting in and out. A little clean engine oil will prevent the action of the restrainer from becoming rough and noisy.

Lubricating the hinge on a hatchback type of boot lid.

Check the free movement of boot and bonnet hinges by opening and closing them. Most need only occasional lubrication.

When necessary, apply engine oil to pivot pins and wipe off any surplus.

Before oiling boot hinges, line the boot with old newspaper to catch any drips. Before removing the newspaper, check hinges and pins for tightness and boot and bonnet panels for alignment.

If adjustments are necessary, see Adjusting catches and hinges.

Rear-hinging bonnets usually have a dovetail bolt which locks at the front to a circular striker plate. If the dovetail is stiff, lubricate with engine oil. Smear petroleum jelly on the striker, where the dovetail lock makes contact.

Front-hinged bonnets usually have a pin-and-striker locking mechanism fitted to the bulkhead. Smear petroleum jelly over metal-to-metal parts.

Changing pedal pads

Use a screwdriver if necessary to remove or to fit a pedal pad.

Peel off old rubber pads and clean the pedal and its stem with a cloth moistened with methylated spirit.

Wet new pads if they are hard to fit. If necessary, use a small-bladed screwdriver as a lever to ease the rubber into place.

Some pads are held by a metal clip. Fit a new clip, bending the fixing pads over the pedals.

Freeing a sticky accelerator cable

If your car has a cable-operated accelerator and the action becomes sticky, the inner cable may have broken strands, which are snagging the outer casing. Loosen the cable at the carburettor, end, detach it from the pedal end, and withdraw it.

Renew a damaged cable as soon as possible. As a temporary measure, unravel broken strands and nip them off with pliers.

Thread a new inner cable from the pedal end. Connect and tighten at the carburettor end, then at the pedal end. Check that it operates correctly at full throttle and the engine idles correctly. If it does not, adjust it, usually at the carburettor end. If the inner cable is stiff but undamaged, inject engine oil into the casing before reassembly.

Place the Outer cable vertically in a vice, gripping it lightly. Mould a Plasticine funnel at the top.

Fill the mould with clean oil and allow it time to seep into the cable assembly – overnight if possible. Do not oil cables with nylon inserts.

Lubricating locks

Smear a little petroleum jelly on the metal-to-metal parts of the door latch.

Smear petroleum jelly on to the parts of the striker assembly where there is metal-to-metal contact. Wipe off surplus.

Nylon striker assemblies must not be oiled. Treat them with a silicone lubricant.

Use graphite powder on the key to lubricate a lock.

Do not use greasy lubricants on keyholes. Such lubricants attract dust and fluff which can hamper the movement of the tumblers.

Ease sticky locks by putting a little graphite powder on to the key before inserting it. Lock lubricant can be bought in an aerosol spray can.